It is in this part that you will need a screen and a keyboard for your Raspberry Pi. May 28, 2020, 5:22am #2. Sign in to view. I do think it is useful to be able to change the volumio user password if the user desires this, but that could be implemented in a later iteration. The first time, a helper will assist you to configure Volumio. Help and Support. How do I now change it back? Tune the volume.
Relax. From my point of view, if the command must run on the volumio account, it is not necessary to use the sudo command because the parent process is “root” or “volumio”. BZH44. This comment has been minimized. This file gets overwritten on each Volumio update so user made changes in /boot/config.txt are not preserved.
Regards, Fabrice. STEP 4: Change the password of your Raspberry Pi Once the file has been modified, you can safely disconnect the memory card from the computer and reinsert it into the Raspberry Pi. For security reasons, SSH is disabled by default on all versions after 2.199. I changed the password (using the passwd command) but now want to change it back to the default but Linux says “Bad: new password is too simple”. Help. Hi, For security issue, can i change the default “volumio” account password (with ssh session) without any malfunction on Volumio2?
Am I wrong?
From MacOs openssh. Copy link Quote reply mbrennwa commented Feb 1, 2020. This is music. Therefore, be patient on the first boot and wait about 5 minutes before starting to use Volumio.The first boot takes longer because it is performing these setup steps: Don't worry if you missed it, you can still configure it later ! If your device has wireless capabilities (and a supported Wireless card) Volumio will create a Wireless network called Volumio, the default password is volumio2 The Hotspot mode will allow you to connect to your Wireless network without the need for a wired connection, just connect to Volumio Hotspot and configure your network in the Network options page
Change Volumio account password? Once it is ready, use to log in: user: volumio. It can be however enabled very easily. Configure Volumio from the WebUi, if you wish to use your NAS as storage; Change the parameters as you wish, to tailor your music experience. Sit in your sweet spot. May 28, 2020, 5:22am #1. Volumio's first boot will take usually longer than normal, up to 6 minutes if you're on a Raspberry PI 1. chsims1. From Linux: commande ssh from a terminal. I think it must be at least 6 characters, contain at least 1 upper & lower case letter & 1 digit. Volumio can display its UI on any attached HDMI display.Once the system is on and you have connected to it through your network or via the hotspot, you will reach Volumio's web-UI. I assume that your v2.119 was a typo (v2.129).At the risk of necro-bumping, I’d just like to add my voice here.Ahhh… (I’d changed the default password, as I do with every device I own Consider IoT security… the first thing anyone tries to “hack” is to login to a product using the product’s name as the username and / or password…Perhaps to move this forward, if the password can be entered in the web interface, at least something could be updated so that the plug-in installation would use that same word in the above command… (please encrypt the password whereever it’s stored so that it’s just decrypted to run the plug-in command)Whilst we’re discussing passwords in plaintext, can we also improve wifi security by not storing the wifi password in plaintext, but use a hash instead?wpa_supplicant.conf can use a hash for the “psk” parameter, so the plaintext entered in the webgui just needs to be put through wpa_passphrase, ie:This works when done manually… my volumio is working fine Perhaps the web interface can run this command when generating the wpa_supplicant.conf file? Example (linux) : ssh volumio@192.168.1.54. When SSH is activated on Volumio (see below how to) you can access your device using: From Windows: Putty. SSH access on volumio. Hello, If you change the password of the volumio user, a plugin install fails with the following in journalctl: And it seems that many commands in volumio use “echo volumio | sudo -S XXX”. password: volumio. If you want to temporarlily change the keyboard layout, you can use the following command: sudo loadkeys fr fr should be replaced by the layout you want. Which is a very sensible thingIs it possible to change password with the latest release 2.119?As far as I am aware, this has not been implemented yet. Type Enter. For security issue, can i change the default “volumio” account password (with ssh session) without any malfunction on Volumio2?The only thing that will not work is the plugin installation, but I will refactor it very soon, allowing to change default password.
The default Volumio password is therefore a problematic choice.